Commercial and Industrial Food Dehydrator Manufacturer Since 1994

dryer repair basics - dryer machine repair

by:IKE Food Machinery     2019-12-15
dryer repair basics  -  dryer machine repair
Dryer repair tips and information may be a beneficial experience for professionals or families to repair the dryerit-yourselfer.
You can save money and gain valuable knowledge and knowledgehow.
Below you will find the steps required to complete some of the most common dryer repairs. Safety: a)
Before attempting any appliance repair, disconnect the power supply by removing the AC power cord on the wall socket.
A small socket can easily carry 150 times the current needed to kill a person. b)
Wear gloves to protect your hands against cuts or tears.
There are many sharp edges from the paper
Metal that is easy to draw blood. c)
Use knee pads to protect your knees from stains. Prevention:a)
Proper maintenance and maintenance is essential to keep the dryer running efficiently.
Improper care can cause your unit to overwork because use more power to keep your clothes dry compared to proper maintenance.
By following these tips, you can extend the life of your clothes dryer, prevent fires and avoid many expensive repairs. b)
Make sure the dryer's feet are horizontal to prevent the machine from being unbalanced, which can cause noise and add wear and tear to the dryer. c)
Clear the lint filter after use for efficient drying and fire prevention.
Clear anything else that might hinder a good airflow.
Don't forget to clean the back of the dryer with lint settling. d)
Vent the dryer outside and never vent it inside.
Clean up the exhaust system at least once a year to remove blockages or other obstacles that hinder good airflow.
Do not ventilate with plastic or vinyl materials.
Many people hire professionals to ventilate and serve the dryer every year.
Knowledgeable technicians can clean all the internal and external dryer pipes into a smooth-running system and help prevent fires. Note: The U. S.
Commission on Consumer Product Safety (CPSC)
Fire related to clothes dryers happens every year, she said. e)
Do not place foam backing carpets, rubber or plastic shoes or other hot sensitive items in the dryer.
In addition, in order to prevent fire, do not dirty clothes or other items with flammable substances such as gasoline and alcohol.
Check the clothes pocket for crayons and other hot sensitive items that might ruin other clothes. f)
Do not overload the dryer.
This could eventually burn the motor.
Component replacement: Please find the model number of the device before starting any equipment repair task.
The dryer model label is located inside the door on the frame.
On some Maytag models, the tag is on the back of the top console.
Write the model number on the online part supply website and find the part breakdown chart.
Ignition replacement: Symptoms of defective flame ignition include: Rolling clothes without heat, long drying time and/or intermittent heat. a)
Find the ignition on the part drawing. b)
Remove the panel to enter the dryer ignition. c)
Remove the plug of the ignition and place the multimeter lead on each pillar of the ignition lead.
Make sure your multimeter is on the ohm scale.
If the measurement is "on", the ignition is replaced.
If it does not measure "on" It does not guarantee that the ignition is good.
The working principle of the ignition is safe.
The current reaches the gas valve through the ignition.
The gas valve is calibrated to open at a specified current.
As the ignition gets hotter, it reduces the resistance, allowing for more current-
Does not flow to the gas body valve until the threshold current is reached and gas flow occurs.
Therefore, you can measure a good Ohm reading on a bad ignition that Burns not hot enough. d)
Remove the screws for fixing the firearms, install the new ones, and tighten the screws.
Be very careful when you do this.
The ignition element is very brittle and easy to break.
A small bump, you will be on your way to the appliance parts store to purchase another firearms. e)
Reinstall the panel and you should be ready.
Test your dryer and hope your replacement has fixed the issue.
Changing the Drum: The symptoms of the defective drum include loud thum bang and/or squeak. a)
Locate the roller on the part drawing. b)
Pay special attention to the details, remove the panel, drum band and drum.
The part needs to be reinstalled correctly when reversing the program. c)
Find and replace the broken roller.
For this you may need a card ring removal tool.
If this tool is not available, you can remove the card ring using a small screwdriver. d)
Use light oil-
3 Oil in 1 is working normally-
Lubricate all rollers before reassembling. e)
Re-install the drums, belts and exterior plates to get the job done.
Test and replacement of heater elements: Symptoms of bad heater elements include unheated dryers.
The drum will still turn. a)
Find the position of the heater element on the part drawing)
Please make sure it is defective before replacing the heater element.
Switch the meter to an ohm scale and measure the continuity between the two legs of the heater element.
If it is open then you find the problem. Replace it.
When removing the old elements, please note all screws, thermostats, etc that need to be returned to the appropriate position when installing the new heater. c)
Replace the panel and turn on the dryer to check the function.
Hot fuse test and replacement: the symptoms of poor heat fuse include a dryer that does not work at all.
The dryer is "dead.
The drum will not turn, but most of the time the internal light will work properly. a)
Find the position of the hot fuse on the part drawing. b)
Remove the panel to locate the thermal fuse. c)
Use the multimeter on the ohm scale to place each lead on each lead of the hot fuse.
You should see a "short ".
If not, then the hot fuse will fuse and need to be replaced.
Please note that many hot fuses will explode due to overheating
Caused by limited external vents
Confined residential vents are common.
In order to prevent the accumulation of lint, air vents should be cleaned every yearup.
Where can I buy a hot fuse?
Find your local appliance repair company, which is usually available for $5 to $20.
If you see it on the Internet, eBay, etc.
You can find it cheaper.
They are a very popular device, so you won't have any problems locating it.
By the way, do not use foil or any other method to bypass it for safety and fire hazards.
You may catch fire in the end.
The hot fuse is intended to explode in a "overheated" state. d)
Replace the panel and test.
Conclusion: As with any home appliance repair work, this procedure may be a very beneficial experience.
Addressing the challenges of new things, learning, and understanding new principles provides personal enrichment and promotes self-confidence.
Take your time and pay attention to the details when you remove and reinstall the electrical parts.
Always disconnect the AC power of the device before starting work.
Electric shock is fatal, so pay attention to the details.
Custom message
Chat Online 编辑模式下无法使用
Leave Your Message inputting...
Thanks. We've received your message. Kindly keep an eye on your email for further updates. Appreciate your patience!